Secure Checkout

Stainless Fuel Hose Kit, Dual Tank w/Under Seat Switch, 66-77 Ford Bronco SKU: 9823

Stainless Fuel Hose Kit, Dual Tank w/Under Seat Switch, 66-77 Ford Bronco

Stainless Fuel Hose Kit, Dual Tank w/Under Seat Switch, 66-77 Ford Bronco

Stainless Fuel Hose Kit Dual Tank w/Under Seat Switch 66-77 Bronco
Purchase Stainless Fuel Hose Kit, Dual Tank w/Under Seat Switch, 66-77 Ford Bronco
$210.00 SKU: 9823
Fits 66-77 Ford Bronco
0 Reviews

Product Overview:

Early Bronco dual tank stainless steel fuel line kit. Use this kit for stock tanks and a carbureted motor. This fuel hose kit will support two fuel tanks and an under seat fuel tank selector switch.

Full description

Early Bronco dual tank stainless steel fuel line kit. Use this kit for stock tanks and a carbureted motor. This fuel hose kit will support two fuel tanks and an under seat fuel tank selector switch.

Early Bronco Fuel Line Kit for Dual Tanks

Here's a one shot kit for your 66-77 Bronco frame-up project. Use this early Bronco fuel line kit for dual tanks and a carbureted motor. This is a dual fuel tank hose kit which includes 21 ft. of stainless steel braided hose, 8 hose ends with clamps, two -6 straight fittings, and a billet fuel filter.
Review Stainless Fuel Hose Kit, Dual Tank w/Under Seat Switch, 66-77 Ford Bronco

California residents: Proposition 65 Warning

Q&A

Have a question? Click Here to submit your question.
Know the answer? Add it here.


Your question will be published after review.


Asked by Taylor, December 6, 2022

Q: Would this stainless line work with a high pressure pump for an efi system?

1 Answer

Answered by sales - December 7, 2022

A: Yes, the stainless hose good for both carbureted and fuel injected systems.

Know the answer? Add it here.

Know the answer? Add it here.

Asked by Weldon, January 20, 2022

Q: What size retaining clips does this fuel line require or what kind of mounting hardware is recommended?

1 Answer

Answered by sales - January 21, 2022

A: The hose is appox. 1/2 od, so our #3111 clips work well. Usually 5 or 6 down the frame will be secure. We have #3104, a SS hex bolt to use into a tapped hole, or a Self tapping may do the same job for you.

Know the answer? Add it here.

Know the answer? Add it here.

Asked by Lucas Passantino, September 7, 2020

Q: I was wondering if this would work with the electric fuel switch

1 Answer

Answered by sales - September 9, 2020

A: Sure, same idea as the manual switching valve.

Know the answer? Add it here.

Know the answer? Add it here.

Asked by Lance, November 22, 2019

Q: What is the OD and ID measurements on this fuel line?

1 Answer

Answered by sales - November 26, 2019

A: The o.d. is approximately 0.550 and the i.d. is approximately 0.340.

Know the answer? Add it here.

Know the answer? Add it here.

Asked by Stephen, November 14, 2019

Q: Is this enough to run from the pump to the carb? And will it work even if I'm running and Elderbrock 4bbl? Thanks for your help

1 Answer

Answered by sales - November 14, 2019

A: Yes, the kit includes enough hose to plumb both tanks to the valve, from the valve to the pump, and pump to carb. We would expect no issues.

Know the answer? Add it here.

Know the answer? Add it here.

Asked by Adam, June 7, 2019

Q: How do you connect to the sending unit at the tank? Also, any special tools needed to assemble the -6 fittings?

1 Answer

Answered by sales - June 11, 2019

A: The hose attaches to the sending unit with a hose clamp. Hand tools only for the -6 fittings, and something to tape and cut the braided hose with are all that is needed.

Know the answer? Add it here.

Know the answer? Add it here.

Asked by Jake, January 23, 2016

Q: How hard is this to install, as I'm guessing the line has to be spliced, are there instructions? Also does the dash fuel selector not work after installation?

1 Answer

Answered by sales - January 26, 2016

A: This replaces the fuel lines from both tanks, to the manual tank switch, then from the tank switch to the engine. The dash switch will work the same as before. There are no specific instructions. You will run the line as you like, and cut to your desired length.

Know the answer? Add it here.

Know the answer? Add it here.

Asked by alan, January 15, 2013

Q: Does this replace the solid steel line from tank to pump.

1 Answer

Answered by WH tech - January 15, 2013

A: Yes, this kit includes 21 feet of stainless braided fuel hose. That is more than enough to do your dual tank early Bronco.

Know the answer? Add it here.

Know the answer? Add it here.

PRODUCT REVIEWS
No Reviews Yet!

Shop popular categories