Secure Checkout

Extreme Dana 30/44 Spindle Bushings, pair SKU: 8844

Extreme Dana 30/44 Spindle Bushings, pair

Extreme Dana 30/44 Spindle Bushings, pair

Extreme Dana 30/44 Spindle Bushings pair
Purchase Extreme Dana 30/44 Spindle Bushings, pair
$44.99 SKU: 8844
Fits 66-77 Ford Bronco
14 Reviews

Product Overview:

These self-lubricating bushings will keep sand and mud out of your spindle much better than the old spindle bearings and will last much longer.

Full description

These self-lubricating bushings will keep sand and mud out of your spindle much better than the old spindle bearings and will last much longer.

Our new Extreme Spindle Bushings will keep sand and mud out of your spindle much better than the old spindle bearings. This means they will last much longer. We believe this will be the last spindle bushing you will ever need!

They fit in snug with no space to allow contaminants between the bushing and axle and that's what you want! No need to add sand attracting grease to our bushings because they are self lubricating.
Review Extreme Dana 30/44 Spindle Bushings, pair

California residents: Proposition 65 Warning

Q&A

Have a question? Click Here to submit your question.
Know the answer? Add it here.


Your question will be published after review.


Asked by Andrew, April 24, 2021

Q: I bought your extreme spindle bushings and before I mess them up. Do these work for chevy small bearing spindles? The id of the spindle is like 1 1/2 And the bushings are like 1 5/8.

1 Answer

Answered by sales - April 26, 2021

A: They will fit the GM 6 bolt Dana 44 Spindle. Press em in! You may also compare to the video on the product page.

Know the answer? Add it here.

Know the answer? Add it here.

Asked by John R Watson, January 26, 2021

Q: After replacing the bearing with this bushing do you still need to putl the very small seal in that goes behind the bearing/bushing that rests up against the bronze spacer?

1 Answer

Answered by sales - January 29, 2021

A: No spindle seal is necessary, as it can trap debris.

Know the answer? Add it here.

Know the answer? Add it here.

Asked by Jason, July 13, 2019

Q: Will these bushings fit spindles/axles for a 78 f250 D44?

1 Answer

Answered by sales - July 15, 2019

A: Yes, we would expect no issue with your F250 Dana 44 spindles/axles. The early Bronco Dana 30 and 44 use the same spindle bearings as your 78 truck.

Know the answer? Add it here.

Know the answer? Add it here.

Asked by Tim, February 24, 2013

Q: Do you still need the spindle bearing seal or is that not needed with the bushing?

1 Answer

Answered by WH tech - February 28, 2013

A: You can use the slinger seal, or you can opt not to. The Extreme Spindle Bushings fit tightly around the axle.

Know the answer? Add it here.

Know the answer? Add it here.

PRODUCT REVIEWS
Michael
Reviewed 12/14/2021
These bushings are nice because they allow use of the tiny OEM seal, which sits right behind them, so water is less likely to get in, and if it does, since they aren't metal, won't rust and seize.

Tom
Reviewed 12/31/2020
These are great, just loaded the dana 44 under my Scout II with a new set of Ten Factory 4340 axle shafts.

BRIAN KENNEDY
Reviewed 07/16/2019
This recent purchase is the second set from WH. I have a 1994 Explorer with a HP D44 front axle out of a 1976 F-150 with 14" Radflo Coilovers. The first set had been installed approximately five years and have been in all kinds of terrain: Highway, freeway, rocks, mountains, desert, overlanding, etc. There was nothing wrong with the first set. They still looked new, but I had to replace a spindle and couldn't figure out how to remove the bushings without damaging them. I decided to replace both spindles and purchased new bushing set because of all the trouble free years I have had with the original set. Great product.

Mark DeWeese
Reviewed 05/20/2019
AFTER SMOKING 2 SETS OF NEEDLE BEARINGS OVER THE YEARS THIS PRODUCT SOUNDED GREAT. THE BUSHINGS FIT NICE AND TIGHT IN THE SPINDLE BORE AND THE AXLE SHAFT. I LOOK FORWARD TO THESE HELP KEEP THE WATER AND GUNK OUT OF MY BEARING GREASE FOR LONGER SERVICE INTERVALS. LOOK OUT FORDYCE CREEK HERE I COME!

Miguel. Salcido
Reviewed 06/28/2018
Hi quality axles. at the best price

Rob morris
Reviewed 11/05/2017
These spindle bushings are way better then the original roller bearings and last longer I had a wheel bearing fail after 5 years in the mud and the spindle bushing is still like new great product

Ron Jones
Reviewed 10/24/2015
these will work better than the old stile bushings or bearings. wont rust while sitting idle

SKTROD
Reviewed 06/01/2015
I don't have any mileage on the bushings yet but I'm sure they are going to be 100% better than the needle bearings. Perfect fit, easy to install.

Tim B
Reviewed 12/15/2014
Thought Id try these bushings so far love them and main reason I purchased these were from the reviews

BDK
Reviewed 10/22/2013
Easy install. Good product. I would recommend this to a friend. Shipping was fast. I had a question about installation and the use of a spindle seal. Called Customer Service, got a quick response to my question.

slewis
Reviewed 10/21/2013
I don't remember where I saw the Extreme Bushings but I was in the process of going thru my Dana 35/44 for my Bronco II when I seen these and knew they were a MUST HAVE. Ordered on-line with no issue. Installed great and can't wait to put them to the test!! Thanks for the great products! (P.S. just wish you offered Bronco II parts also. Lots of Bronco II, Explorer, and Ranger owners out here).

bronconut
Reviewed 03/19/2013
These new spindle bushings are a neat concept. Just another one of WH's better ideas.

Nick H.
Reviewed 07/15/2011
After seeing all the dirt that got packed into the original spindle bearings, I decided to try these Extreme Spindle Bearings. They went in easy and provide a tight seal.

Road Toad
Reviewed 04/30/2009
I met the guy who manufactures this product at the 40th Bronco event in northern Wisconsin about 2 1/2 years ago and I bought a pair directly from him at that time. WOW was I surprised and happy to see this product on the Wild Horses web site! Now I have a source to get another pair when I upgrade my next Bronco. I've had my current set installed for over two years now, have experienced no issues with them, and they have worked EXCELLENT. No more wreaking of the bearing surface on the stub shaft like the old bearings would do when they get filled with crap, rust, or just goes to heck with age. Get yours ordered today!!!!


Shop popular categories
4,93 stars