WH Armor Plate Bumper

Item #: 4004NET

The Wild Horses Plate Bumper bolts into the stock bumper mounts on your 1966-1977 Bronco frame. It only weighs about 55 lbs.

Read 8 Reviews | Write a Review

Read 6 Customer Questions | Ask a Question

Installation PDF

Watch Videos

This item will receive FREE SHIPPING to anywhere in the 48 contiguous states. The shipping charge for this item will have already been deducted from the shipping charge shown in checkout.
Customers outside of the 48 contiguous states will be emailed the shipping charges for approval prior to shipping.

Price:

Description

WH's all new USA made Armor Plate bumpers pack a punch. These 3/16" steel plate bumpers weigh in at about 55 lbs. The relatively light weight bumper bolts into the stock bumper mounts on your 1966-1977 Bronco frame. We have designed them with a full 2" of adjust-ability in 1" increments. This allow you to move the bumper up to fill in the gap created by a body lift without any modifications. The bumper is designed as a front bumper but may also be used on the rear provided you are not running a tire rack. They give your rig a clear, no-nonsense look and add much needed protection for your classic Bronco.

* 3/16" plate steel

* Full 2" of adjustability in 1" increments

* Mounting hardware included

* Ready for paint or powder coating

Watch the Video!

WARNING: This product may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
www.P65Warnings.ca.gov

WH Armor Plate Bumper
Item #: 4004NET

Qty.

Videos

Product Briefing

Installation

Installation Instructions

SUGGESTED PRODUCTS

Armor-Geddon Tail Guards / Rear Quarter Panel Protection

5653

~~$1,049.98~~ $795.00

Product Reviews
Write a review

Design is beefy and some messy grinding

Oct 9, 2021  |  By Sean Albright

I like the look of this bumper even though it's heavier duty than needed. I thought the typical Bronco gap would have been eliminated but it's not. I'm going to make my own spacers and use a T-bolt or carriage bolt on the top to get a lower profile and to raise the bumper up more. Also want to slide it into the frame more so will need to notch at the corners to clear the quarter rockers. Still will need a filler, maybe rubber, to fill the gap. Directions give good advice not to add finish until mocked up. I can live with all of the above. My complaint is the fabricator ground down one weld to much on one side and the body line changes, is pitted, and not flat. Looks pretty bad if you are picky but if you are rock crawling should not be an issue. I guess I will live with it. Decent price.

Great piece

Jun 12, 2020  |  By David Ogiony

Quality plus! The bends and welding are spot on!

Wild Horses Armor Plate Bumper

Apr 25, 2020  |  By Travis Barr

Excellent fit and finish. Another high quality piece from Wild Horses! Would highly recommend!

WH plate bumper

Dec 30, 2019  |  By MICHAEL TAMEZ

Great quality bumper with easy instructions. Used rattle can to finish it off and cut into the rear to install a hitch. They came out amazing.

Bumper

Jul 14, 2019  |  By Mark Palomo

Excellent fit to the 76 Bronco.

Armor plate bumper

Dec 1, 2018  |  By Eric Figgins

These are clean looking and well built bumpers.

Armor Tough

Jul 26, 2018  |  By Dave W.

Bought two of these. Fit perfect and is a huge improvement over the stock chrome bumpers. Great great price too!! Been looking for replacement bumpers and everything I found were several hundred dollars more than these. Wild Horses is the place to get your early Bronco parts!!

Good Looking bumper

Jun 17, 2018  |  By Phil B

Actually a well made bumper. Looks good and adjustable in 1 inch increments depending if you have a body lift or not. Mine took little grinding for a good fit and I also welded a 2 inch receiver for a hitch. Ended up buying another for the front.

Q&A